Alpine’s goal is to give customers powerful amps that take up a minimum of space, and this has been achieved as never before with the PDX amps.

The PDX-1.1000 is also extraordinarily small and efficient. In fact, the power supply is so efficient that the amp does not need a heat sink. All the power goes into output, not heat.

Features

* (SPK Connect)

* 4Layer Glass Epoxy PC Board

* Class-D

* Layered Installation

* 1 Channel (Mono) Operation

* Thermal Management Processor

* Subsonic Filter

* Adjustable Crossover (LP)

* MOSFET Power Supply

* DC-DC PWM Power Supply

* Discrete Pre-Amp Stage

* MOSFET Final Outputs

* STAR Circuitry

* Auto Over-Current Protection

* Top Mounted Blue LED Power/Status Indicator

* Integrated Wire and Mounting Screw Terminals

* One Side Terminal Layout

* Gold Plated RCA Input Connectors

* Continuously Adjustable Gain Control

* Gold Plated Power Screw Terminals

* Non-Fading Pre-Amp Output

* Dimensions: 257mm x 192mm x 62mm

RMS Power

* [2ohms @14.4V 1%THD]: 1000W x 1 (20Hz - 200Hz)

* [4ohms @14.4V 1%THD]: 1000W x 1 (20Hz - 200Hz)

Bass Engine® Sound Tuning

* Crossover Frequency Adjustment: 50Hz-200Hz, -24dB oct (LP)

In the PDX-4.150, Alpine met the challenge of producing a full range digital amplifier to rival the sound quality of even the best high-end Class A/B amplifiers. They use improved feedback circuitry to faithfully reproduce the input signal for improved dynamic range and higher fidelity. A revolutionary power supply filtering system, lower switching frequencies and lower output impedance combine to create extremely low distortion and greater speaker control, for clarity that meets or exceeds that found in the best Class A/B amplifiers.

Features

* (SPK Connect)

* 4Layer Glass Epoxy PC Board

* Class-D

* Layered Installation

* 4/3/2 Channel Operation

* Thermal Management Processor

* Adjustable Crossover (HP/LP)

* MOSFET Power Supply

* DC-DC PWM Power Supply

* MOSFET Final Outputs

* STAR Circuitry

* Auto Over-Current Protection

* Top Mounted Blue LED Power/Status Indicator

* Integrated Wire and Mounting Screw Terminals

* Input Channel Selector

* Input Mode Selector Switch

* One Side Terminal Layout

* Gold Plated RCA Input Connectors

* Continuously Adjustable Gain Control

* Gold Plated Power Screw Terminals

* Dimensions: 257mm x 192mm x 62mm

RMS Power

* [2ohms @14.4V 1%THD]: 150W x 4

* [4ohms @14.4V 1%THD]: 150W x 4

Bass Engine® Sound Tuning

* Crossover Frequency Adjustment: 1/2Ch + 3/4Ch, 30Hz-400Hz HP/LP/Off

* (-12dB/oct)

MRP-M2000

Mono Power Amplifier

* Overview

* Specifications

CEA-2006 Power Rating

CEA-2006 Power Rating (40hm@14.4V = 1%THD+N), S/N 75dBA (Ref. 1W into 4Ohm): 2000W x 1

RMS Power (at 14.4V THD+N, 20-200Hz)

Per channel into 4 ohms: 1500W x 1 (0.08% THD)

Per channel into 2 ohms: 2000W x 1

Need ground shakin' power?

The MRP-M2000 is the most powerful amplifier Alpine has ever made. Get ground-pounding bass and the subwoofer set-up of your dreams.

Industry-leading Power and Control

Power and control go hand in hand with this amplifier. Alpine’s high-power mono amp Class-D design gives you more power, cleaner signal and tighter, deeper bass without draining your battery. Class-D provides continuous clean power to your speakers, operating at 80% efficiency far greater than conventional Class-A or B amplifiers. The MRP-M2000 high damping factor yields tight, accurate, controlled bass. Translation: Enjoy cleaner bass, even during extreme power demands.

Enormous Power in a Compact Size

Designed for the audio enthusiast, the ultra compact PDX series amplifiers deliver enormous power output and sound quality while operating at 90% efficiency.

General

* Amplifier Type: Class-D

* Channel Design: 4 Channel + 1 Channel (Mono)

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: Direct FET Power

* Board Circuitry: STAR Circuitry

* Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top/Side Mounted LED Power/Status Indicator

* RCA Input: Gold Plated RCA Input Connectors

* Speaker-Level Inputs: No

* Crossover: Adjustable Low-Pass/High-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Pre-Amp Stage: Discrete

* Board Design: Dual Sided Glass Epoxy PC Board

* Gain Control: Continuously Adjustable Gain Control

Install

* Terminal Layout: One-Side

* Screw Mount / Wire Cover: Insert Screw Terminals and Plug-in Speaker Terminals

* Install: Stacking Install

Specifications

* MAX Power Ratings

* Total Max Power 760W

* RMS Power Ratings

* Per channel into 4 Ohms (@ 14.4V @1%THD+N, 20Hz - 20kHz for 4CH, 20Hz - 200Hz for Mono) 50W x 4 + 300W x 1

* Per channel into 2 Ohms: N/A

* Bridged into 4 Ohms: N/A

Sound Tuning

* Crossover 30Hz-400Hz, -12dB/oct. (Low-Pass/High-Pass for 4CH), 20Hz-200Hz, -24dB/oct. (Low-Pass for Mono)

* EQ (Equalizer): No

* Subsonic Filter: 15Hz (Fixed), -24dB/oct. for Mono

Dimensions

* WxHxD mm: 257mm x 62mm x 192mm

General

* Power Requirements: 14.4V DC (11V to 16V)

* Input Sensitivity: 0.2 - 4.0V

* Frequency Response: 20 - 20kHz (0, -1dB) for 4CH, 20 - 200Hz (200Hz, -3dB)

* Speaker Impedance: 4 or 2 Ohms

* Signal to Noise: 100dBA

Features

Power Density Ratio Design

DC-DC PWM Power Supply

Discrete Pre-Amp Stage

Switch-mode Digital Amplification

Subsonic Filter (30Hz/50Hz selectable)

S.T.A.R. Circuit

1 Preout

High Temperature Protection

Over Current Protection

Variable Crossover

Layered Installation Capability

Quick Connect Speaker Terminal

Same Power into 2ohms and 4ohms

Power Specification

1500W MAX Power

1 x 600W RMS (2ohms, 14.4V, 1% THD)

1 x 600W RMS (4ohms, 14.4V, 1% THD)

S/N Ratio (IHF A Weighted ) 110dBA

Frequency Response 20Hz - 200Hz (20Hz +/-1dB, 200Hz –3dB)

Crossover Frequency 50Hz - 200Hz (-24dB/oct)

Input Sensitivity (V/at 10k ohms) 0.1 - 8.0V

Dimensions 257 (W) x 192 (H) x 62 (D) mm

Weight 3.11kg

Sometimes size doesn't matter. You get big power from a little box with Alpine's Power Density Digital Amplifiers. Super-efficient Class-D technology allows these small-but-mighty amplifiers to run so cool they can be stacked together for a sweet multi-amp setup, freeing up valuable space in your car.

Features

* Power Density Ratio Design

* DC-DC PWM Power Supply

* Discrete Pre-Amp Stage

* Switch-mode Digital Amplification

* S.T.A.R. Circuit

* High Temperature Protection

* Over Current Protection

* Variable Crossover

* Layered Installation Capability

* Quick Connect Speaker Terminal

* Same Power into 2ohms and 4ohms

Power Specification

* 800W MAX Power

* 4 x 100W RMS (2ohms, 14.4V, 1% THD)

* 4 x 100W RMS (4ohms, 14.4V, 1% THD)

* S/N Ratio (IHF A Weighted) 96dBA

* Frequency Response 20Hz - 200Hz (20Hz +/-1dB, 200Hz –3dB)

* Crossover Frequency 30Hz - 400Hz (-12dB/oct)

* Input Sensitivity (V/at 10k ohms) 0.2 - 4.0V

* Dimensions 257 (W) x 192 (H) x 62 (D) mm

* Weight 3.11kg

Alpines smallest range of amps to date, great output smart looks and the ease of being installed nearly anywhere in a car make for a great audio experience.

General

* (SPK Connect)

* 4Layer Glass Epoxy PC Board

* Class-D

* Layered Installation

* 1/2 Channel Operation

* Thermal Management Processor

* Adjustable Crossover (HP/LP)

* MOSFET Power Supply

* DC-DC PWM Power Supply

* MOSFET Final Outputs

* STAR Circuitry

* Auto Over-Current Protection

* Top Mounted Blue LED Power/Status Indicator

* Integrated Wire and Mounting Screw Terminals

* One Side Terminal Layout

* Gold Plated RCA Input Connectors

* Continuously Adjustable Gain Control

* Gold Plated Power Screw Terminals

* Dimensions: 257mm x 192mm x 62mm

RMS Power

* [2ohms @14.4V 1%THD]: 150W x 2

* [4ohms @14.4V 1%THD]: 150W x 2

Bass Engine® Sound Tuning

* Crossover Frequency Adjustment:

* 30Hz - 400Hz HP/LP/Off (-12dB/oct)

Install Under the Front Seat

These amplifiers are so compact, they can even be installed under a seat! That’s right, put 1,000 watts under a seat, instead of filling up the trunk. The controls on the front are still accessible.

* Compact enough for under-seat installation.

* Convenient controls and terminals make installation easy.

* Put the mono amp under one seat and a fullrange amp under the other seat to hide away the entire amplifier system.

Low Resistance, High Current Speaker Terminals

When you disconnect an amp it is hard to connect again because you don’t know the polarization, but the PDX amps eliminate that problem. You just plug the speaker cables into the terminals – you can’t do anything wrong.

* Error-free connections.

* Much faster and easier.

* Convenient installation with pre-wired connectors

Small Footprint

The illustration shows how amazingly compact the PDX amplifiers are as compared to the previous MRD-M1001.

* About 60% smaller than previous models with same power output.

* Makes it possible to build a serious sound system with powerful bass — without filling up the boot!!

Same Power Output into 2Ohm and 4Ohm

The ability to provide the same output to 2Ohm and 4Ohm provides greater system building flexibility.

* Mono amp has two subwoofer connectors, making it easy to add a second subwoofer.

* Same amount of power used to drive one 4Ohm speaker can drive two 4Ohm speakers when they are wired in parallel to create a 2Ohm load.

* Efficient way to get more dynamic bass.

Full Range Class-D Amplification

Class-D amplification provides extremely high efficiency, with power losses much lower than with other types of operation. The PDX amps set new benchmarks for performance and accuracy. They use an advanced power supply, custom DSP processor and a true digital Class-D circuit for superior power production and efficient operation.

Excellent Sound Quality

In the PDX-4.150 and PDX-2.150, Alpine met the challenge of producing a full range digital amplifier to rival the sound quality of even the best high-end Class A/B amplifiers. They use improved feedback circuitry to faithfully reproduce the input signal for improved dynamic range and higher fidelity. A revolutionary power supply filtering system, lower switching frequencies and lower output impedance combine to create extremely low distortion and greater speaker control, for clarity that meets or exceeds that found in the best Class A/B amplifiers. All three amps benefit from the use of trickle down technology from the AlpineF#1Status amplifier.

Amazing Power Density Ratio

Alpine’s goal is to give customers powerful amps that take up a minimum of space, and this has been achieved as never before with the PDX amps. We have even developed a new way to measure this performance, called the Power Density Ratio. To find it, divide the total RMS power from all channels by the total displacement volume of the amplifier in cubic centimeters (WxDxH).

The PDX-1.1000, for example produces an impressive 0,27 watts per cubic centimeter. Competitors only achieve a Power Density Ratio of about 0,13. The PDX-1.1000 is also extraordinarily small and efficient. In fact, the power supply is so efficient that the amp does not need a heat sink. All the power goes into output, not heat.

Layered Installation

All of the new PDX series amplifiers share an identical form. Using the removable 1” diameter trim caps from the top of the amplifiers, the amplifiers can be vertically stacked on top of each other and share one set of mounting holes — an industry-first installation option.

* Can stack up to 3 PDX amps without increasing footprint of installation space.

Designed for high performance and value, Alpine’s wide selection of sound system solutions provide powerful, high-quality sound for every vehicle.

Power up your system with Alpine’s V-Power amplifiers. These amps provide outstanding power output, flexibility and value with a bold, stylish design.

Features

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

General

* Amplifier Type: Class-D (Digital)

* Channel Design: 1 Channel (Mono)

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker Level Inputs

* Crossover: Adjustable Low-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Board Design: Dual Sided Glass Epoxy PC Board

* Gain Control: Continuously Adjustable Gain Control

Specifications

* Total Max Power: 1900W

RMS Power Ratings:

* Per channel into 4 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 200Hz) 600W x 1

* Per channel into 2 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 200Hz) 1000W x 1

Sound Tuning

* Crossover: 50Hz-200Hz, -24dB/oct. (Low-Pass)

* EQ (Equalizer): Bass EQ (Fixed Frequency): 50Hz 0 to +12dB

* Subsonic Filter: 15Hz (Fixed), -24dB/oct.

* Dimensions:

* Foot Print (WxHxD) mm: 380mm x 60mm x 242mm

* Heat Sink (WxHxD) mm: 320mm x 60mm x 242mm

General

* Power Requirements: 14.4V DC (11V to 16V)

* Input Sensitivity: 0.2 - 4.0V

* Frequency Response: 20 -200Hz (200Hz/-3dB)

* Speaker Impedance: 4 or 2 Ohms

* Signal to Noise: 100dBA

Designed for high performance and value, Alpine’s wide selection of sound system solutions provide powerful, high-quality sound for every vehicle.

Power up your system with Alpine’s V-Power amplifiers. These amps provide outstanding power output, flexibility and value with a bold, stylish design.

Features

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

General

* Amplifier Type: Class-A/B

* Channel Design: 4/3/2 Channel

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker Level Inputs

* Crossover: Adjustable Low-Pass/High-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Pre-Amp Stage: Discrete

* Final Outputs: Non-Fading Pre-Amp Output

* Board Design: Dual Sided Glass Epoxy PC Board

* Gain Control: Continuously Adjustable Gain Control

Specifications

* Total Max Power: 1320W

RMS Power Ratings

* Per channel into 4 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 20kHz) 100W x 4

* Per channel into 2 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 20kHz) 150W x 4

* Bridged into 4 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 20kHz) 300W x 2

Sound Tuning

* Crossover: 50Hz-400Hz, -12dB/oct. (Low-Pass/High-Pass)

* EQ (Equalizer): Bass EQ (Fixed Frequency): 50Hz +12dB

* Subsonic Filter: 15Hz (Fixed), -18dB/oct.

Dimensions

* Foot Print (WxHxD) mm: 380mm x 60mm x 242mm

* Heat Sink (WxHxD) mm: 320mm x 60mm x 242mm

General

* Power Requirements: 14.4V DC (11V to 16V)

* Input Sensitivity: 0.2 - 4.0V

* Frequency Response: 20 -20kHz (0, -1dB)

* Speaker Impedance: 4 or 2 Ohms

* Signal to Noise: 100dBA

Alpine’s amazing new IMPRINT Sound technologies have overcome all acoustic problems in the cabin – tuning your car interior’s sonic environment to perfection and letting you hear music just as the artist intended.

IMPRINT Sound is a stunning new suite of sound processing technologies that let you sit in the producer’s chair and hear music exactly as it was meant to be heard. It delivers sonic accuracy never before available in the car, and utilises sophisticated professional sound tuning technologies, including MultEQ, that measure your car’s acoustics and process the sound – precisely and automatically!

Designed for high performance and value, Alpine’s wide selection of sound system solutions provide powerful, high-quality sound for every vehicle.

Power up your system with Alpine’s V-Power amplifiers. These amps provide outstanding power output, flexibility and value with a bold, stylish design.

Features

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

General

* Amplifier Type: Class-D (Digital)

* Channel Design: 1 Channel (Mono)

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker Level Inputs

* Crossover: Adjustable Low-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Board Design: Dual Sided Glass Epoxy PC Board

* Gain Control: Continuously Adjustable Gain Control

Specifications

* Total Max Power: 1100W

RMS Power Ratings

* Per channel into 4 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 200Hz) 300W x 1

* Per channel into 2 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 200Hz) 500W x 1

Sound Tuning

* Crossover: 50Hz-200Hz, -24dB/oct. (Low-Pass)

* EQ (Equalizer): Bass EQ (Fixed Frequency): 50Hz 0 to +12dB

* Subsonic Filter: 15Hz (Fixed), -24dB/oct.

Dimensions

* Foot Print (WxHxD) mm: 270mm x 60mm x 242mm

* Heat Sink (WxHxD) mm: 210mm x 60mm x 242mm

General

* Power Requirements: 14.4V DC (11V to 16V)

* Input Sensitivity: 0.2 - 4.0V

* Frequency Response: 20 -200Hz (200Hz/-3dB)

* Speaker Impedance: 4 or 2 Ohms

* Signal to Noise: 100dBA

Designed for high performance and value, Alpine’s wide selection of sound system solutions provide powerful, high-quality sound for every vehicle. Power up your system with Alpine’s V-Power amplifiers.

These amps provide outstanding power output, flexibility and value with a bold, stylish design.

Features

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

* Amplifier Type: Class-A/B

* Channel Design: 4/3/2 Channel

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker-Level Inputs

* Crossover: Adjustable Low-Pass/High-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Pre-Amp Stage: Discrete

* Final Outputs: Non-Fading Pre-Amp Output

* Board Design: Dual Sided Glass Epoxy PC Board

* Continuously Adjustable Gain Control

Features

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

* Amplifier Type: Class-A/B

* Channel Design: 4/3/2 Channel

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker-Level Inputs

* Crossover: Adjustable Low-Pass/High-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Pre-Amp Stage: Discrete

* Final Outputs: Non-Fading Pre-Amp Output

* Board Design: Dual Sided Glass Epoxy PC Board

* Continuously Adjustable Gain Control

Specifications

* Total Max Power: 640W

RMS Power Ratings

* Per channel into 4 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 20kHz) 50W x 4

* Per channel into 2 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 20kHz) 75W x 4

* Bridged into 4 Ohms: (@ 14.4V +-1%THD+N, 20Hz - 20kHz) 150W x 2

Sound Tuning

* Crossover: 50Hz-400Hz, -12dB/oct. (Low-Pass/High-Pass)

* EQ (Equalizer): Bass EQ (Fixed Frequency): 50Hz +12dB

* Subsonic Filter: 15Hz (Fixed), -18dB/oct.

Dimensions

* Foot Print (WxHxD) mm: 270mm x 60mm x 242mm

* Heat Sink (WxHxD) mm: 210mm x 60mm x 242mm

General

* Power Requirements: 14.4V DC (11V to 16V)

* Input Sensitivity: 0.2 - 4.0V

* Frequency Response: 20 -20kHz (0, -1dB)

* Speaker Impedance: 4 or 2 Ohms

* Signal to Noise: 100dBA

KTP-445 - HEAD UNIT POWER PACK

Add On and Build Up Your System

This compact upgrade instantly boosts the power of your system. Easy to install with no additional wiring, it fits neatly behind your head unit.

* 4 x 100W MAX

* 4 x 45W RMS

* Works with all 2005 - present Alpine head units

* Plug & Play installation (no additional wiring required)

* High/Low gain switch

* Compact size

FEATURES

Install

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

General

* Amplifier Type: Class-A/B

* Channel Design: 4/3/2 Channel

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker-Level Inputs: Speaker Level Inputs

* Crossover: Selectable Low-Pass / High-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Pre-Amp Stage: Discrete

* Final Outputs: Non-Fading Pre-Amp Output

* Gain Control: Continuously Adjustable Gain Control

SPECIFICATIONS

Max Power Output Ratings

* Total Max Power: 640W

RMS Power Ratings

* Per Channel into 4ohms (≤1%THD+N): 4 x 50W

* Per Channel into 2ohms (≤1%THD+N): 4 x 75W

* Bridged into 4ohms (≤1%THD+N): 2 x 150W

Sound Tuning

* Crossover Frequency (Fix, OFF/LPF/HPF Selectable) 1/2 ch: 80 Hz (-18dB/oct)

* Crossover Frequency (Fix, OFF/LPF/HPF Selectable) 3/4 ch: 80 Hz (-18dB/oct)

* EQ (Equalizer): Bass EQ Fixed Frequency 50 Hz _ Selectable Gain 0/+6/+12 dB (3/4ch)

Dimensions

* Footprint: 270 mm x 60 mm x 242 mm

General

* Power Requirements: 14.4 V DC (11 V to 16 V)

* Input Sensitivity: 0.2 - 4.0 V (RCA IN)

* Input Impedance: RCA IN 10k Ω / SP IN 10k Ω

* Frequency Response: 10 Hz - 50 kHz (+ 0,-1 dB)

* Speaker Impedance: 4 or 2 Ω

* Signal to Noise: S/N Ratio (IHF A Weighted, Reference: rated power into 4ohms) 90 dB

* Weight: 3.0 Kg

Huge power output of 350 watts gives this little beast the ability to run some big bass in your ride, maybe consider running one on each side of your front speakers for serious vocal definition.

Features

* 1 Channel Operation

* BassEngine®

* Subsonic Filter

* Bass EQ Circuit

* Crossover (LP)

* MOSFET Power Supply

* DC-DC PWM Power Supply

* Discrete Pre-Amp Stage

* Double Buffered Pre-Amp Input Circuitry

* STAR Circuitry

* Top Mounted Blue LED Power/Status Indicator

* Continuously Adjustable Gain Control

* Speaker Level Inputs

* Gold Plated Power Screw Terminals

Gold Plated Speaker Terminals

* Cross-Vented Chassis Design

CEA-2006 Power Rating

* CEA-2006 Power Rating (40hm at 14.4V = 1%THD+N), S/N 60dBA (Ref. 1W into 4Ohm): 200x1

RMS Power (at 14.4V THD+N, 20Hz-200Hz)

* Per channel into 4 ohms: 200W x 1 (1.0% THD)

* Per channel into 2 ohms: 350W x 1 (1.0%)

* Total Max. Power: 700W

BassEngine® Sound Tuning

* Crossover Network: 18dB/oct

* Low Pass Crossover Frequency (Adjustable): 50Hz – 200 Hz

* Subsonic Filter (Fixed): 15Hz @ 24dB/oct.

* Bass EQ Frequency (Fixed): 50Hz

* Bass EQ Level (Adjustable): 0 - 12dB

General

* Power Requirements: 14.4V DC (11V to 16V)

* Frequency Response: 20Hz – 200kHz (+0, -3dB)

* Signal to Noise (S/N): 90dBA (referenced to rated power)

* Input Sensitivity (For Rated Power): 0.2V to 4.0V

* Input Impedance: 10k Ohm

* Speaker Impedance: 4 or 2 Ohm (Stereo)

* Dimensions (WxHxD): 199mm x 60mm x 267mm

* Dimensions (WxHxD): 7-4/5" x 2-2/5" x 10-1/2"

* Weight: 2.52 Kg. (5 lbs. 9 oz)

FEATURES

Install

* Terminal Layout: Two-Sided

* Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals

General

* Amplifier Type: Class-A/B

* Channel Design: 2/1 Channel

* Thermal Control: Thermal Management Control

* Power Supply: DC-DC PWM Power Supply

* Power Supply Design: MOSFET Power

* Board Circuitry: STAR Circuitry

* Current Protection: Over-Current, Over-Voltage and Thermal Protection

* Power Indicator: Top Mounted Blue LED Power Indicator

* RCA Output: Gold Plated RCA Input Connectors

* Speaker-Level Inputs: Speaker Level Inputs

* Crossover: Selectable Low-Pass / High-Pass

* Connector Plating: Gold Plated Input, Output, Power and Speaker Terminals

* Pre-Amp Stage: Discrete

* Final Outputs: Non-Fading Pre-Amp Output

* Gain Control: Continuously Adjustable Gain Control

SPECIFICATIONS

Max Power Output Ratings

* Total Max Power: 320W

RMS Power Ratings

* Per Channel into 4ohms (≤1%THD+N): 2 x 50W

* Per Channel into 2ohms (≤1%THD+N): 2 x 75W

* Bridged into 4ohms (≤1%THD+N): 1 x 150W

Sound Tuning

* Crossover Frequency (Fix, OFF/LPF/HPF

* EQ (Equalizer): Bass EQ Fixed Frequency 50 Hz _ Selectable Gain 0/+6/+12 dB

Dimensions

* Footprint: 210 mm x 60 mm x 242 mm

General

* Power Requirements: 14.4 V DC (11 V to 16 V)

* Input Sensitivity: 0.2 - 4.0 V (RCA IN)

* Input Impedance: RCA IN 10k Ω / SP IN 10k Ω

* Frequency Response: 10 Hz - 50 kHz (+ 0,-1 dB)

* Speaker Impedance: 4 or 2 Ω

* Signal to Noise: S/N Ratio (IHF A Weighted, Reference: rated power into 4ohms) 90 dB

* Weight: 2.0 Kg

Kenwoods no nonsense amplifier range comes up with a small but powerfull 2 channel amplifier, happy to run anything from a pair of components to a subwoofer.